T-fiberglass Beams is our company's high-quality livestock used slat flooring system support equipment, which is a kind of Fiberglass Beams, it looks like the letter "T" from the side. Made of a special antifreeze, high temperature material, ranging in size from 110mm to 120mm, with ruggedized features. T-fiberglass beams installation and use of very convenient, is a very good agricultural farming equipment. We can produce according to your special requirements, can also be produced according to your drawings. Our commitment to our products, our T-fiberglass beams are of high quality and easy to use. Looking forward to your patronage.
T-fiberglass Beams T-Fiberglass Beams,Durable T-Fiberglass Beam,T-Fiberglass Beam For Farrowing Crates,Strong T-Fiberglass Beam HuangHua FengYi Honde Metal Factory , https://www.farrowingcratesfromchina.com
Thresher Frequently Asked Questions and How to Adjust
The thresher has the advantage of high work efficiency and ease of use. Therefore, the current usage rate is high. However, there are a series of problems with the thresher. The following are several situations in which threshing machines often occur during the threshing process. Analyze the causes of various situations and attach them to repair methods. for reference. First, the cause of threshing is not clean: the feeding amount is too large or the feeding is not uniform; there is a threshing gap between the pattern bar and the concave plate; the rotation speed of the roller is too low; the grain is too moist. Adjustment methods: 1. Reduce the amount of feed, even feeding. 2. Correctly adjust the threshing gap. Replace worn parts with prompt wear. 3. The pulley of the power machine and the pulley of the thresher should be reasonable. If the pulley slips and turns, the tension pulley should be adjusted to tighten the belt. 4. Straw over wet grain should be properly ventilated, then drying and then threshing. Second, the reasons for poor seed cleanliness: lack of air flow fan, mostly fan is too loose, forming a belt drive slip, causing the fan speed can not meet the design index, or due to the looseness of the fan pulley screw to form a pulley idling, can not normally drive the fan Rotation; too much crop stalk entry into the drum. Repair methods: 1. Check the tightness of the fan drive belt, too loose should be properly adjusted tension pulley, the pulley tension to the appropriate degree; if the fan pulley fixing screws loose, should be fastened. 2. Reduce the amount of feed or feed the gap correctly. Third, the cause of serious jams: too much moisture in the grain, too much feeding; the drum speed is too low; the drum is damaged due to damage to the drum; the concave plate is heavily worn or damaged; the feed chain is slack or the clip gap is too large, causing the drum Too much grass. Adjustment methods: 1. Properly reduce the amount of feed, and keep the feed evenly. 2. Check if the power is sufficient or the voltage is too low and if the power is reasonable. At the same time, it is also necessary to check the power transmission belt tension and whether the belt slips and spins. 3. If the roller bar is damaged, it should be repaired in time. 4. Repair or replace the concave plate. 5. Adjust the tightness of the feed chain, and also check the tension of the suction fan belt and the fan speed. Fourth, the excessive fragmentation of grain causes: the threshing gap is too small or the drum speed is too high; the feed is uneven or the grain is too dry or too wet. Adjustment methods: 1. Check whether the threshing clearance is correct, and the minimum gap of general wheat threshing should not be less than 4mm. In addition, it is necessary to check whether the matching of the drum pulley and the power pulley is reasonable and accurate. If something is wrong, it should be adjusted or replaced. 2. As far as possible to ensure uniform feeding, more dry cereal feed, humidity and feed. 5. Excessive grains discharged from the dust outlet Cause: The amount of exhaust air is too large; the holes in the concave plate are blocked. Repair methods: 1. First check whether the fan speed meets the requirements, if not meet the adjustment, adjust the fan pulley diameter to check whether it is properly equipped. 2. Shutdown, power off, and clear plug holes in the wells.